Background

quantity of aggregate in one mile of 4 lane road

Calculations for Road Maintenance - Utah LTAP

Calculating quantity of concrete order for sidewalk Problem 8 • Given: 4" Sidewalk 5 feet wide, ... (1/road width ft.) x (9sft/sqyd) • SOLUTION: • 1169 ft. 9 ... Tons of aggregate per mile Tons of aggregates required per mile for various rates of application problem 11 ...

Cost Estimating Guide for Road Construction

Montana Base Excavation $/Mile for Road Widening with Linear Grading, ¾:1 cut slope 66 Table 45. Montana Base Excavation $/Mile for Road Widening with Linear Grading, 1:1 cut slope . 66

4. ESTIMATING ROAD CONSTRUCTION UNIT COSTS

4.1 Introduction. The unit cost of road construction in dollars per kilometer is the sum of the subunit costs of the road construction activities. Road construction unit costs are estimated by dividing the machine rates by the production rates for the various activities involved in road construction.

Calculating How Much Gravel You Need for Your Driveway ...

Gravel should be a minimum of 4-inches deep. The smaller the gravel, the more even the coverage will be. If rocks are on the larger side, allow for an additional 1/2 inch. Using 2 inches for the depth, the following measurements are a guide to the amount of gravel coverage per ton: 1/4 to 1/2 inch gravel, 100 square feet per ton; 1/2 to 1 inch ...

Minnesota's Aggregate Resources: Road to the 21st Century

and infrastructure. One of the most highly visible uses for aggregate materials is in road construction and maintenance. Road construction accounts for about 25% of the aggregate used in Minnesota in any given year. • There are more than 133,000 miles of roads in Minnesota. This figure does not include recreational trails or forest roads.

Gravel Calculation Chart - National Center For Rural Road ...

CUBIC YARDS PER MILE Width of the roadway in feet 12 14 16 18 20 22 24 26 28 30 1 244.44 285.19 325.93 366.67 407.41 448.15 488.89 529.63 570.37 611.11

DESIGN AND CONSTRUCTION GUIDELINES FOR FULL DEPTH ...

explorations are 4 per lane mile (e.g. 2 lane roadway by 1 mile long = min. 8 drill holes). For FDR projects extending longer than one mile and uniform conditions are observed, sampling can be reduced to 1 per lane mile. Consult with the Regional Materials Engineer for the appropriate sampling quantity.

Cost Per Mile Models - FDOT

New Construction 4 Lane Urban Road with 22' Median and 4' Bike Lanes: U05: $8,055,245.51. Composite Report: New Construction 4 Lane Divided Urban Interstate, Closed 22' Median with Barrier Wall, 10' Shoulders Inside and Out U06 : $13,129,720.94. Composite Report: New Construction 5 Lane Undivided Urban Arterial

Generic Cost Per Mile Models

New Construction 4 Lane Urban Road with 22' Median and 4' Bike Lanes $6,889,753.96 Composite Report New Construction 4 Lane Divided Urban Interstate, Closed 22' Median with Barrier Wall, 10' Shoulders Inside & Out $10,495,660.87 Composite Report

Materials in Use in U.S. Interstate Highways

The 1.5 Gt of aggregates estimated to be in interstate highways is more than 50 percent of the combined estimated sand and gravel and crushed stone used in construction in the United States in 2005. The 35 Mt of asphalt used in 2005 is slightly more than the total esti-mated asphalt and road oil used in the United States in 2000 (Kelly, 2005).

average cost per ton mile to haul aggregate by truck ...

Crushed stone ( aggregate) – North Carolina Geological Survey. In the foreground diesel-powered 50- ton -capacity haul trucks are loaded by …. One mile of typical 2-lane asphalt road with aggregate base requires about 25,000 …. The year-end average price of aggregate was $ per ton at the plant site. » More detailed.

Gravel Driveway Calculator - Estimate Material for a ...

Gravel is commonly sold by the cubic yard, so to find the material needed for a driveway, you need to find the volume in yards. Calculate How Many Cubic Yards of Gravel You Need. Estimating gravel driveway materials is as simple as estimating the cubic yards of volume the driveway needs to be. Cubic yards are found by multiplying the length by ...

Roadway Fill Volume Calculator

Calculator Use. Calculate (estimate) roadway or parking lot material fill requirements for construction or maintenance projects. Allows common road materials or custom entry so you can enter your own material density. If you need additional materials in the drop down menu you can contact us and make a …

ASPHALT CALCULATOR [How Much Asphalt do I Need ...

Imagine I want to pave over an area measuring 20 feet by 4 feet to a thickness of 6 inches using standard asphalt (140 lb/ft³) and costing $150 per US short ton. I want to have an estimate for the volume of asphalt required, along with its weight in tons and total cost.

What amount bitumen used in road construction per 1 km ...

Answer (1 of 8): It cannot be said with this much of information. Bitumen is provided in road construction in various forms like BM (Bituminous Macadam), DBM (Dense Bituminious Macadam), BC (Bituminous Concrete), SDBC (Semi Dense Bituminous Concrete), Bituminious emulsions (Prime Coat/Tack Coat)....

Frequently Asked Questions - The American Road ...

In the lower 48 states, there are 72 million lane-miles of road. Between 2000 and 2016, the U.S. built an average of 30,427 lane miles of roadway per year, adding 63.4 square miles per year to the amount of land covered by roads. At this pace, it would take 180 years to increase the U.S. land mass covered by roads to even 1 percent.

Gravel Calculator | How much gravel do you need?

First, we need to divide the pea gravel path into four rectangles: 1, 2, 3, and 4. Now, we have to measure the width and width of each sector: Sector 1 has the length of 10 yd and the width of 0.5 yd; Sector 2 has the length of 4 yd and the width of 0.5 yd; Sector 3 has the length of 4 …